Zero Tolerance 350 vs. Emerson CQC-7: Hard use testing (часть 4)

Hi all! We’re establishing with hard use trying out of Emerson CQC-7 and zero Tolerance 350 This sequence of trying out will in the end investigate Which this type of knives is better as a "folding pry-bar" Zero Tolerance 350 has some skills after preliminary trying out in common cutting tasks but this expertise will disappear if it would abruptly fail these main checks seeing that in any case, these knives are "folding pry-bars" neither than just right , light , secure cutters Let’s get began! We’re establishing with checking out of cutting edge begin with reducing of cable you’ll find the marks on the coating correct away I don’t know if it can be damaged but there are marks Now Emerson each knives did very well no chips no nothing however it’s only a "warming-up" moving to a extra severe taks at present now we have a can of pineapples we will be able to open one aspect via Zero Tolerance and an additional facet with the aid of Emerson Go simply drain the juice I remind that there’s an S30V steel right here This truth of itself is a significant statement considering that powder steel is a powder metal collapse out and chipping is feasible And 2d facet by way of Emerson the feeling is that this left-facet chisel grind is made for this form of labor it could even be visible how clean is an Emerson’s cut and how raggedly it used to be cut with the aid of Zero Tolerance Battery has died at inappropriate moment I was about to examine the slicing edges And i will be able to definitely say to you that cutting edge Zero Tolerance feels quite bad.I do not know if it will be visible on video without macro… I.E. There is not any very big chips however it used to be broken in an unpleasant approach And Emerson feels excellent good, I made some conclusions after my first expertise of tough use trying out and that i decided to add an additional experiment of innovative. This experiment will likely be a shaving of this aluminum plate. This can be a industrial 2mm aluminum – "saucepan" aluminum. And i will attempt to shave it cautiously. Carefully does no longer work. And we are going to shave as it is coming to hand. I have no idea how it may be visible: Zero Tolerance takes off the shavings superb, at that without any further injury to innovative i.E. The damage that’s already there’s stays nevertheless it doesn’t get worse. That is how it shaved. Now Emerson. Emerson is coping with this assignment very well too. With correction on the fact that this left-aspect chisel tries to come out and does not diggind deep into the material. However however it shaved this aluminum and nothing foremost occurred to this cutting edge. No chippings or deep crumples.Very good! Now relocating to a subsequent stage. It is going to be a stage of trying out the locks. That is very intriguing. By the way, the knives did not received any play. Zero Tolerance had some micro blade-play. Incidentally, pay concentration to blade coating on Zero Tolerance after aluminum – it can be received painted from it. Normally the Zero Tolerance had some micro blade-play via a intent of it being assited. And Emerson is "lifeless"-tight. Let’s go! Commencing with Zero Tolerance. Adequate Holds. Holds. 5 excellent strikes and it standed all of them. Now Emerson with it is thinner titanium liner. Like this… Emerson, which is in theory have to be sticking, has folded.I feel it’s folded and opened. Like this. I consider the whole thing is understood right here. Lock is put good enough. On the primary sight the whole thing is looking quality however the way it folds… I completely did not expect this… Well, moving on. Moving to checking out of tip strength. We will be penetrating a gap in a timber block. Now we have 10 strikes. Now 10 strikes with Emerson. Not unhealthy on both knives but Emerson seems to enter the wood more aggressively and deeply. I believe it needs to be noticeable how heavy are the side masses on a knives. I began to punch in one-of-a-kind spots… That is it. To the bone. Rapid this time. My hand had slided off on a few occasions on the Emerson. Practically on the blade.The knife is not s lengthy and it didn’t went extra. Manage of Zero Tolerance additionally has it can be drawbacks i’m going to no longer going to say it now however simplest about Emerson. I confirm what men and women say that if no longer guard your self with a thumb, the hand could slip to a leading edge. I verify that. After that we have a next test of tip strength – tin-plate 0.8mm 5 strikes each and every. Zero tolerance – the very-very tip is long past. It can be actually a tenth of mm And listed here are it is inlets. Now Emerson. Here is a correct inlet! The coating on Emerson is began to fly off via flakes. Here you can find. But the coating on Zero Tolerance is also stripped on a tip here.Subsequent a tuffer test with tin-plate of 1mm. 5 strikes. It was very very rough for Zero Tolerance. Now Emerson. Appear at a couple of holes made by way of Emerson, right here and right here. This one is entered the prior gap however this one and my feelings say that penetrating with a tanto is of path much more handy Oh, the tip is broken here. Oh Emerson… Pay concentration the tip itself and this place…Right here…I don’t know Shavings began to come off the cutting edge. I do not know easy methods to exhibit this i am hoping it should be seen good enough then…Additionally I additionally ready a chrome steel. Industrial non-magnetic stainless-steel. It’s not a tin but in addition 1mm. However I won’t are trying the tip of each knives on it. Ooooooooh….FUCK! How i haven’t seen this? Seem at Zero Tolerance. At the tip. That is what you get with S30V, so at these exams persons Emerson turns to be higher Of direction how we will speak concerning the staintless metal? There will be no stainless steel. WOW! I will need to sit down and estimate the results of this trying out. So what? Let’s do slightly of batonning ultimately. Both knives don’t seem to be relatively enjoyable. I’m doing batonning with released lock seeing that liner will not stand up to it .Battoning is finished across the fibers to experiment the burden on pivot. Emerson just doesn’t want to enter the wood it jumps off. Ok, the entire construction appears to maintain good no play, nothing. Zero Tolerance seems to do batinning better I mean the way it enters the material, going superb. With Emerson all that is extra sad. Good, I feel we will conclude on that. I imply the "energetic" a part of checking out and transfer on to excited about the outcome of what we now have got due to the fact it wasn’t all apparent. Let’s take a detailed look at our fighters. Of path it became a shock for me that this piece of tin-plate, 1mm thickness grew to become an insuperable barrier for both of them. With the one that went first – Zero Tolerance 350. Chipping on the tip. After opening a can i clearly understood that hanging a metal like S30V on a folding pry-bar is not a excellent idea. You can see these chippings. It’s all grew to become to be after opening a can and it is large chip at the tip is grew to be a culmination of all.I believe that coating holded up very good. All these paint marks might be washed off. Lock started to move slightly extra. It was once at the very starting and now going closer to middle. The knife itself: blade is centered, velocity-safe is working it is very most important Now – Emerson looking at the tip. 1mm tin-plate used to be too rough for it despite the fact that it used to be penetrating it a lot better than Zero Tolerance. But chips , even on 154CM metal, which isn’t tempered to a best possible hardness via Ernest Emerson i.E.It’s particularly flexible metal but it didn’t standed to it. But again, it penetrated so much deeper. I remind, these 2 holes, this and this is Emerson. These small ones is Zero Tolerance. In some of them the tip wasn’t even rather penetrating. This one for illustration… It can be only a point. But innovative after opening a can, is a clean Emerson’s victory. However chips are very severe too.Tip itself is damaged. And colossal disappointment is that this titanium liner, which closed after hanging the back of the blade. It can be understood that it can be no longer a correct use however Zero Tolerance withstood well and Emerson failed to. And for the knife that is put as an unbreakable pry-bar it is a minus. However in summation of all tests it is needed to carefully accumulate all my feelings and results. Knives are going to be resharpened and after bringing them again to normal shape we are going to talk in small print about tough use checking out and assessment of these knives more commonly that’s all, thanks for staring at, hope it was once exciting, for me in my view it gave the look of adequate action See you, bye bye

Add Comment